Plastering Is decorative Invoice "DECOR"

Plastering "DECOR" is intended for the high-quality invoice decoration of surfaces indoors (without the subsequent painting) and the finishing for the purpose of giving to them architectural expressiveness and operational reliability.

Application  of plastering depending on its position in the building or the construction and the acting on it load:

- internal walls and ceilings in the accomodations with the usual humidity of air;
- internal walls and ceilings in the moist accomodations.

Advantages Of decorative Plastering "decor":

- high adhesion to the base;
- low capillary water absorption;
- high resistance to cracks (low shrinkage);
- high compressive strength.

Price is contractual, vzavisimosti from the demands of the customer
(color, the structure of invoice decoration, the volume of party).

Glue for the tile is developed and intended for the revetment of walls and floors of ceramic, glazed tile, mosaic, etc., by tile in the dry, moist and damp  accomodations, and so the revetment of facades.
Glue for the tile can be used as repair composition with the levelling off of concrete and brick surfaces and for eliminating the small defects in the form of shells, cracks and other unevennesses.

Basic indices of Clay for the tile of "extra":

packability;
high water-holding ability;
the high fixing ability - absence of the effect of the sliding down of the tile, packed to the fresh solution;
high elasticity;
high adhesion strength with the bases (with the varied conditions of hardening).

The plastering of extra this is nonshrinking plaster mixture (shielding- decoration) with the polymeric additives.
Plastering is intended for the high-quality plastering of walls inside and outside the accomodations
(possibly without the subsequent painting) for the purpose of giving to them architectural expressiveness and operational reliability.

- high adhesion to the base;
- low capillary water absorption;
- the high permeability to steam (constructions not are less than in previous it is layer);
- high resistance to cracks (low shrinkage);
- frost resistance;
- weather resistance;
- the water-repellent effect;
- high compressive strength.

Plastering from 66 rubles for the bag 50 kg.

Putty is intended for the qualitative finishing of facade and other surfaces,
walls in the dry, moist and wet accomodations for further coloring and gluing of any coating.

Also the this suitable for puttying composition is intended for the closing of shells, unevennesses  (with depth to 2 mm) on the bases from the concrete and the plastering.
With the aid of the puttying is created not having times, cracks, scratches, dents and other defects the smooth and uniform surface, suitable after grinding or without the grinding) for the subsequent finishing: painting or pasting by wall-papers. Putty approaches under each concrete form kraski(vododispersionnye, organorastvorimye, oil, etc.).
It is important to note that the polymer-mineral suitable for puttying composition is universal and compatible practically with all forms of paints.

This finishing putty "tonic quartz" is produced with the use of super- white Danish cement of brand M-700, thus potverzhdayetsya the super- whiteness of putty, unsurpassed strength because of the basis: quartz of powdered (silica flour)  and  to high-quality imported additives has  quality and convenience in the work.
The technology of the production of putty is patented by company trowel and does not have patronymic analogs.

         Traditionally in the place with the journal "Mir of building" we let out to this exhibition the number of the periodical, where they placed their advertisement on the first page of cover and material about the firm inside the periodical on the turn. Periodical enjoyed on the exhibition enormous demand. For active uchatiye in this vystvke OOO "trowel" is entrusted the certificate of exhibition.

   Nonshrinking mixture with the complex of the khimichechkikh additives and the granules for the device of the ideally smooth, high-strength, resistant to the abrasion tightening devices of floors as the carrying layer in the basements, the garages, of workshop, and also for the levelling off horizontal surfaces under any coating. Cast concrete (drainer) also to widely ispol'zuyet'sya as fine-grained concrete for foundation, cast, etc.
   The application of unique additives and special formulas - considerably increases the plasticity of solution with simultaneous decrease in the consumed water, which leads to an increase in the strength, wear resistance and adhesive strength.  It is used with the carrying out of internal and external works.

        Technological effectiveness, method ELOTEKS

MISCIBILITY - lekaya or hindered; spontaneous or retarded.

CONSISTENCY - softer or is thicker; high or low viscosity; stickiness; thixotropy; stability.

APPLICATION - lung or difficult; uniform texture; sanitary properties.  

                                      Stability of trowelling to the abrasion, standard EN 12808-2  

  After the process of mixing in accordance with standard EN 196-1 trowelling is brought to the plastic sheet and is covered with glass plate with the plastic edges on the edge of solution. During the rotation is formed the disk of the solution with a thickness of 5 mm. after 24 hours of 2 models carefully tyuey premeshchayutsya and they are stored in accordance with the requirements for the dry storage with 23S/50% RH. After storage in the course of 28 days is conducted the test to the abrasion with the aid of abraziometra in accordance with standard EN ISO 10545-6 or as in Elotekse with the aid of the abrasive instrument Of taber. The mnimal'noye requirement of the loss of material after 50 cycles - is not more than 2000 mm^e. 

                                      Bending strength, EN 12808-3

  After the standard process of mixing in sootvetsvii with En196-1, tile trowelling is applied to the steel charging box (Dl y'0mm, Sh of ya0mm, into ya0mm) by two layers. Each layer is packed by 60 impacts with the aid of the impact machine. In the first 24 hours of 3 models of each composition they are covered with glass. After 24 more it is hour models they take out themselves from the charging box they are stored in accordance with the requirements for the dry storage and the freeze- thawing. The test to the bending strength is conducted after shelf-life. Minimum requirement for the trowellings - e..shchYu/mm^2.

                       Compressive strength, EN 12808-3

  After the standard process of mixing in accordance with En196-1, tile trowelling is placed into the steel charging box (Dl y'0mm, Sh of ya0mm, into ya0mm) by two layers. Each layer is packed by 60 impacts with the aid of the impact machine. During first 24 it is hour, 3 models of each composition are covered with glass. After 24 more it is hour models they are moved away from the charging box they are stored in accordance with the requirements for the dry storage and the freezing -otaivani4. The test to the compressive strength is conducted after shelf-life. By minimum requirement for the trowellings it is 15 h/mm^2. 

                                                         Shrinkage of 1-28 days, EN 12808-4

  After the standard process of mixing in accordance with En196-1, tile trowelling is applied into steel mul'du(Dl of y'0mm, Sh of ya0mm, into ya0mm) by two layers. Each layer is packed by 60 impacts with the aid of the impact machine. After 24 hours of 3 models of each sotava they take out themselves and are stored with 23S/50% RH. Initial or basic measurements are conducted with the aid of the micrometer. Any shrinkage or expansion can be observed with the repeated measurement in 28 days. Minimum requirement for the shrinkage is a change in the length not more than to 2mm/m^y after 28 days. 

                                                       Sorption capacity of solution, EN 12808-5

  After the standard process of mixing in accordance with En196-1, tile trowelling is placed by 2 layers into the steel charging box (Dl 2*80mm, Sh of ya0mm, into ya0mm), which is divided in half. Each layer is packed by 60 impacts of impact machine. The models take out themselves after 24 hours and are placed to sukhoyekhraneniye to 21 days with 23/50% RH. All 4 sides of model seal up by silicone. After 28 days of dry storage, is conducted the test to adsorbtstyu of water on 6 prisms for each formula. Is measured a gain in weight of model due to the water after 30 minutes and after 240 minutes with contact 5 and 10 mm with the water over the area of ya0*ya0 mm. a maximum gain in weight for the standard tile trowelling - 5 deg. for 30 min and 10 deg. in 240 min.

                                                          Lateral deformation, EN 12002

  Miscibility  (lung or heavy - usual or retarded)

  Consistency  (cream-like either thick- high or low viscosity -M4kga4, cream-like or sticky-Thixotropic-Sticky- stable)                                                        

  Putting  (lung or heavy- wavy)

                                                                        Wettability, EN 1347

Are plotted glass tiles through 10, 20 and 30 min. to the fresh tile glue, which is substituted by trowel by the kinks of '*' mm to the dry concrete substratum. After piling of each tile to the solution, load by weight 5 kg. on 30 s. later 30 min. Is visually determined how well tile it is moistened by fresh solution and/or how much pasting solution naliplo to it with the detachment. The result of moistening is evaluated in % (area). Up to now requirements are not yet determined.

                                                                       Testings of the hardened solution - adhesion, EN 1348

  The nesorbiruyushchaya tile is plotted to the solution 5 min after the batch, which is substituted by trowel by the kinks of '*' mm to the concrete slab with the low adsorption of water. Then it loads weighing 2 kg. on 30 s.. Through the specific spaces of storage of models under the dry, moist conditions, and also with the heating or the freezing thawing are conducted the tests to the detachment. Besides the value of adhesion, is important also the breaking load. Requirement of the standard: 0,shch/mm2 for Sy and 1.0N/mm2 for S2 the field of the different methods of storage.

                                                                      Determination of sliding down, EN 1308

  The pasting solution is brought by trowel by the kinks of '*' mm to the concrete slab with the low adsorption of water. Distance is measured, the measuring rule is removed and plate is tipped up. Only then after 2 min., 2 nesorbiruyushchiye tiles with the size of y0*y0 cm by the weight of 200g. are plotted to the fresh solution and nakgruzhayetsya with weight 5 kg. on 30 s. The spacer between the tile and the steel rule is moved away and is measured the distance between each tile and steel rule on top. Substratum tips up 90 degrees. After 20 min., they place substratum horizontally, and is measured the difference between each tile and steel rule. Requirement: sliding down not more than 0,shchmm after 2min for SYT or S2T it is glue.

                                                                          Open time, EN 1346

  It is such to testing for detachment on EN 1348, but instead of piling of tile after 5 min., it is plotted through 5, 10, 20, and 30 min. Instead of the nesorbiruyushchey tile for this test is used the vodosorbirushchaya tile. Test is conducted after 28 days of dry storage with 23 with 50 % RH. Requirements of the standard: open time 0.shchN/mm^2 for SИ of tile it is glue after 30 min..                                                 

                                                                                  Lateral deformation, EN 12002

Samorastekayushchayasya, flexible mixture of cement, natural mineral fillers with the complex of chemical additives for levelling off and leveling of bases and concrete coatings with building  and remote of the accomodations of different designation. It is used for the subsequent final coating (linoleum, tile, parquet). It possesses significant wear resistance, low shrinkage, increased by stability to the abrasion.

Jointing mixtures are prepared on the highest demands of today's buyer, the base color: WHITE, colored and toning are produced TO ORDER.

Is developed technologically effectively new sand-concrete "SUPER-LAYER"according to the results of testing it showed the highest indices along the strength, the convenience in the work and the spectrum of the application: for the device of high-strength wear-resistant floors, carrying layer in the basements, the garages, the workshop, production accomodations, foundation, cast, etc.
It is used with the carrying out of internal and external works in the damp and moist accomodations.